This juicer is designed to juice ingredients like fruits and vegetables.
Do not use the juicer for extracting vegetable oil.
Do not juice ingredients with high contents of vegetable/ animal oil.
If vegetable/animal oil gets on the juicing screw or the strainer, this can aff ect the performance of the juicer and could result in damaged parts.
After juicing, if the juicer is not cleaned right away, the remaining pulp inside the top-set can dry up which can make disassembling and cleaning hard. This can also aff ect the juicer’s performance and color.
Ingredients that are rich in carotenoids such as carrots and spinach may dye plastic parts. When the parts are dyed with carotenoids, rub vegetable oil in to the dyed areas and use mild detergent to clean.
Vegetable oil should only be used during clean-up for parts that are discolored. Do not use vegetable oil on the juicing screw or the strainer. If vegetable oil or oil from animal fat gets on the juicing screw or the strainer, this can aff ect the juicer’s performance and may result in damaged parts.
The silicone pieces on the top-set can be detached to be thoroughly cleaned.
Ingredients like celery or ginger contain long fibers that may wrap around the juicing screw and affect the juicer’s performance. When juicing fibrous ingredients, do not collect more than 500 g per session. After juicing this quantity or less, clean the top-set completely before juicing again.
If the compression silicone on the bottom of the juicing bowl is not plugged in correctly, the juice may seep out on to the juicer base. Before assembling the parts, check and make sure the compression silicone is plugged in correctly.
After juicing, let the juicer operate for another 30 seconds to extract the remaining pulp.
If there is too much pulp in the top-set, this can cause the drum lid to not open. In this situation, press the REVERSE OFF - FORWARD button in this order, switching back and forth 2 to 3 times.
Pour water down the feeding tube to rinse out the insides and then try opening the drum lid.
Depending on the density of the ingredients, the extracted juice may show layers of diff erent juices. It is diff erent from separation due to oxidation caused by juicing with a high-speed juicer.
Check if the parts are assembled correctly. Try reassembling the parts and listen for the odd noise.
Do not start the juicer unless there are ingredients and/or liquid in it.
Operating the juicer without ingredients can cause damage to the screw.
If the juicer is operated without ingredients or liquid, the noise level can increase and also can lead to damage.
The friction noise from the juicing screw and the strainer will disappear when ingredients are inserted into the juicer.
If the noise occurs when ingredients are inserted into the juicer, check the size of the ingredients. Do not insert anything over 2,5 cm in thickness.
Depending on the type of ingredients, the dimensions can be smaller.
The noise can occur if the juicer is operated on an uneven or slanted surface. Place the juicer on a horizontally fl at surface when operating.
When continuously juicing, and depending on the ingredient, the juice may contain a lot of fi ne pulp.
To reduce the fi ne pulp, clean the top-set frequently and extract the pulp.
Use a mesh strainer and put the juice through it to collect the unwanted pulp.
If the strainer and the screw are damaged and aff ecting the juicer’s performance, it is recommended the parts be replaced.
The lifetime of each part may vary depending on length and method of use and ingredients extracted.
If too many ingredients are inserted at the same time, it may cause the juicer to stop frequently. This can lead to pulpy juice. Insert the ingredients slowly and few at a time.
It is completely normal that juicing bowl is shaking little bit while operating.
Each fruits or vegetables to be juiced may produce a different amount of juice.
Even same fruits or vegetables can have different amount of juice due to the freshness of the fruits or vegetables.
To extract more juice out of the refrigerated fruits or vegetables, put it in the clean water and wait until the fruits or vegetables are moist enough to be extract.
Carrot has a low fiber which it is hard to extract it, to get a best result extract carrot with different high fiber fruits or vegetables. Such as, kale, leafy green vegetable. Please cut the carrot into quarterly to get a best result.
Check if the pressure silicon is assembled properly.
Too much fruits or vegetables in the screw or over heated motor may stop the appliance in middle of using. Please wait until the appliance is cool down to use it again.
Please place the motor around cool temperature area.
When using the fruits or vegetables with the hard seed in it, please remove all the seeds in the fruits or vegetables to use. It may break down the strainer.
Once you have finished juicing place both hands on the juicer bowl and twist to the right with the top and take it to the sink
Remove the top and give it a rinse in warm water, if you feel it needs some detergent, apply it
Separate the rotation wiper with the screen and juicing screw from the juicing bowl
Tip the screen upside down into your hand so the juicing screw falls into your hand
Separate the rotation wiper from the screen
Place all parts into a sink of warm soapy water or rinse thoroughly under warm water
When cleaning the juicer bowl you are required to take out the rubber plug under the juicing bowl to rinse through any excess pulp that may be left, use the end of the brush provided to help you push it through, put the plug back in once cleaned. This is something that can easily be forgotten, so try to remember. If you forget the juicer bowl will not fit properly on the base of the juicer and will not start. Or if it does start it will add pressure to the juicer and not give you the best juice possible, with extra pulp coming through to your juice
Washing the screen properly is very important because if you leave any excess pulp on the screen the quality of your juice will be lower. It is very easy to clean put the screen under warm water and with the brush provided this should be a 1 minute job. If you have juiced a lot and you have excess pulp on the screen you can use the end of the brush and scrap it off before brushing it under warm water
Once you have rinsed all the parts put them on a towel to dry
The whole cleaning process should take between 2 to 5 minutes
To assemble the juicer refer to the notes above on how to assemble the juicer
It is important to note the cleaner you keep your juicer parts the better performance you will get from your juicer. Try not to build any excess juice residue on the parts.
We have eco friendly cleaning material you can order from us if you need to.
No you cannot wash the parts in the dishwasher.
Some plastics are BPA Free therefore does not contain the chemicals that allow it to be dishwasher safe.
Cleaning process is very simple, just pull the three parts apart and rinse in warm water or wash how you wish,
Brush the little fibre that is caught in the basket for about a minute and everything should be clean.
Ensure you check the groove under the juicing screw is cleaned properly before reassembling juicer.
Also ensure you plug in the rubber plug under the bowl to seal the part completely before juicing again.
Ensure the juicer does not build any residue film stain on the parts.
Ensure you assemble the juicer correctly by following the red dot system
Firstly unpack all parts in the box and put on a kitchen bench or table
Unwrap all the plastic and separate all the parts
Place the base of the juicer near a power point ready for use
Take the strainer and put it into the rotation wiper, give it a turn so it naturally turns easily
Take the Juicing screw and place it in the strainer, allow it to drop in naturally
Check under the juicing bowl and ensure rubber seal is sealed
Place the rotation wiper with the strainer, place the juicing screw in the juicer bowl
Place the juicing bowl on the base of the juicer where the red dot is, ensure it is placed comfortably and the juicing screw can turn
Place the Hopper Lid on top of the Drum Lid
Place the lids on the juicer bowl where the red dot is and then click it to the left to lock it in
Then turn on the juicer for use
Note the juicer will not start unless all the above is in place
For safety reasons all the parts need to follow the red dot system
